How to check diesel exhaust fluid is a routine task that keeps your truck running smoothly. The process takes only a few minutes and requires no special tools. Most drivers can do it themselves before a long haul.
Ignoring the DEF warning can lead to costly engine derating.
Per ISO 22241‑1, DEF must be 32 % urea and 68 % deionized water. Manufacturers recommend checking the level every 300, 500 miles or at each oil change. If the dipstick shows low, add fluid using a clean funnel and record the mileage.
Now let’s walk through the exact steps to verify the level and reset the system.
Problem / Pain Point: Low DEF Warning & SCR Failure
The Selective Catalytic Reduction (SCR) system reduces NOx emissions by up to 90 % when DEF is maintained. A low DEF warning light means the SCR catalyst may run dry, causing power loss and higher fuel use. Ignoring the alert can lead to expensive catalyst replacement and emissions violations.
If you need to add fluid, see adding transmission fluid for proper handling techniques. For diagnosing the warning, a quick scan with an OBD‑II scanner can confirm the fault code.
How to Check Diesel Exhaust Fluid

How to check diesel exhaust fluid: locate the amber reservoir near the fuel tank. Remove the cap and insert the dipstick to read the level mark. If low, add DEF using a clean funnel and record the mileage.
Reset the warning light if equipped, then continue driving.
Step-by-Step Process / How to Guide
Start by gathering the items you’ll need.
| Item | Purpose | Typical Cost (USD) |
|---|---|---|
| DEF reservoir dipstick | Reads fluid level | $5 |
| Clean funnel | Prevents spills | $3 |
| Amber DEF container (5 L) | Refill supply | $12 |
| Safety gloves | Protects hands | $4 |
| OBD‑II scanner (optional) | Confirms fault codes | $20 |
Next, follow these steps:
- Locate the DEF reservoir near the fuel tank.
- Remove the reservoir cap and wipe the area clean.
- Insert the dipstick fully, then pull it out to read the level.
- If the level is below the “Full” mark, pour DEF slowly through the funnel.
- Re‑cap the reservoir, tighten securely, and wipe away any spills.
- Start the engine and check for the DEF warning light to clear.
- If the light remains on, use an OBD‑II scanner to clear the code.
- Record the mileage and date for your maintenance log.
For full emissions requirements, see EPA Tier 4 emissions requirements. Also refer to ISO 22241‑1 for exact composition details.
Common Mistakes to Avoid / Common Errors
- Using windshield washer fluid instead of DEF can ruin the SCR catalyst.
- Overfilling the reservoir can cause spillage and contaminate the fuel system.
- Ignoring temperature limits in cold climates leads to crystal formation.
- Forgetting to reset the warning light after refilling leaves the system in fault mode.
- Adding contaminated water or fuel to the DEF supply degrades performance.
Costs / Pricing / Data / Specs
As of 2026, average DEF price is $3.50 per gallon, and a typical Class 8 truck uses about 1 L per 100 L of diesel. Reservoir capacities range from 5 L to 10 L, so most drivers refill every 300, 500 miles. For comparison, a typical headlight bulb costs about $15, similar to DEF refill rates.
Keeping the fluid level correct saves fuel and avoids costly repairs.
Frequently Asked Questions
How often should I check the DEF level?
Check the level at each routine oil change or every 300, 500 miles. Regular checks prevent unexpected warnings.
What happens if I run out of DEF?
The engine will derate, losing power and fuel efficiency. The SCR catalyst may be damaged if left dry for an extended period.
Can I use any brand of DEF in my truck?
Yes, as long as it meets ISO 22241‑1 specifications. All approved brands have the same 32 % urea concentration.
Do I need special tools to add DEF?
No. A clean funnel and the vehicle’s dipstick are sufficient. Wear gloves to avoid skin contact with the fluid.
How do I reset the DEF warning light?
After refilling, start the engine and let it idle for a minute. If the light stays on, use an OBD‑II scanner to clear the code.

