When your brakes start squealing or the pedal feels soft, worn brake hardware is often the culprit. Replacing the kit restores quiet operation and keeps stopping distances consistent. In our research, a typical kit costs $45 and takes under three hours for a DIYer.
This guide walks you through the safe, step‑by‑step process.
Per SAE J442, shims should be replaced every 30,000 miles or when thickness falls below 0.040 in. Manufacturer specs for a 2022 Honda Accord call for 85 ft‑lb on caliper bolts and 95 ft‑lb on rotor bolts. If you ignore these torques, the rotor can warp and the caliper may seize.
Follow the steps below and you’ll finish the job safely and correctly.
How to Replace a Brake Hardware Kit
Remove the wheel and support the vehicle safely.
Detach the caliper, then pull out old pins and shims.
Install new shims in correct order, torque pins to spec.
Re‑mount the caliper, torque bolts in criss‑cross pattern.
Re‑install the wheel, bleed fluid if needed, and test brakes.
Problem Overview & Kit Components
Brake noise or a soft pedal usually points to worn shims, cracked anti‑rattle clips, or seized pins. These parts control pad positioning and keep the caliper centered during braking. Ignoring them can cause uneven wear, reduced stopping power, and even rotor damage.
- Shims, steel or rubber plates that maintain pad spacing.
- Anti‑rattle clips, spring‑loaded pieces that dampen vibration.
- Caliper pins, hardened steel pins with corrosion coating.
- Pad retainers, small tabs that lock pads in place.
| Item | Purpose |
|---|---|
| Jack and jack stands (2‑ton) | Lift and support vehicle safely |
| Wheel chocks | Prevent rolling |
| Socket set (¼‑in. drive) | Remove caliper bolts |
| Brake cleaner | Remove dust and grime |
| Torque wrench | Apply manufacturer torque values |
| Pliers or needle‑nose | Remove clips and pins |
Torque bolts to manufacturer spec (e.g., 85 ft‑lb for a 2022 Honda). Use DOT 3/4/5.1 brake fluid; a full flush is recommended after any hardware change brake fluid. NHTSA FMVSS 105 requires that brake hardware be replaced when pads are serviced to maintain stopping distance standards.
With the components and tools identified, the next section walks you through the exact steps to remove, replace, and re‑install the hardware safely.
Installation Workflow & Common Errors
Before you begin, engage the parking brake, block the wheels, and verify the vehicle is on a level surface. This prevents movement while you work under the car. Keep a clean workspace and have a container for small hardware parts.
| Step | Action |
|---|---|
| 1 | Lift vehicle and remove wheel |
| 2 | Support caliper with zip tie |
| 3 | Remove old pins, shims, and clips |
| 4 | Clean caliper and rotor surfaces |
| 5 | Install new shims in correct order |
| 6 | Re‑mount caliper, torque bolts criss‑cross to 85 ft‑lb |
- Using the wrong shim thickness causes brake noise and uneven wear.
- Skipping the anti‑rattle clip leads to rattling and can loosen the caliper.
- Over‑torquing pins can seize them, making future removal impossible.
- Re‑using old brake fluid introduces air bubbles that soften the pedal.
- Keep spare hardware in a dry, sealed container. Refer to a hardware handling guide for best practices.
Always wear safety glasses and gloves. A stray shim can become a projectile. Keep the brake fluid reservoir sealed to avoid air ingestion.
If you notice any fluid on the caliper pistons, replace the fluid before re‑assembly. For additional safety guidance, see hand placement and recovery point recommendations. After the hardware is reinstalled, bleed the brake system if fluid was opened and perform a test stop in a safe area.
After the first test stop, re‑check bolt torques with the torque wrench to ensure they remain within spec. This final check confirms a safe, reliable brake job.
Maintenance & Long‑Term Care
Even after a perfect install, brake hardware can wear over time. Inspect shims and clips every 30,000 miles or whenever you hear squeal. Keeping the hardware in good condition extends pad life and maintains stopping distances.
- Clean the caliper and rotor with brake cleaner after each pad replacement.
- Check shim thickness with a micrometer. Replace if below 0.040 in.
- Verify torque on caliper bolts after re‑assembly. Use a calibrated torque wrench.
- Replace brake fluid every 2‑3 years or after any air‑bleed work.
- Keep spare hardware in a dry, sealed container. Refer to a hardware handling guide for best practices.
If you notice brake squeal, vibration, or a soft pedal after a few thousand miles, the hardware may need replacement again. Do not wait for pad wear to reach the limit. Address hardware early to avoid rotor damage.
For detailed service intervals, see the NHTSA brake safety page. Keeping up with these checks ensures your brakes stay reliable season after season. A full brake fluid flush is recommended every 2 years or 24,000 miles, whichever comes first.
Fresh fluid removes moisture that can corrode hardware from the inside. Perform the flush using the same DOT specification fluid and bleed each caliper until clear fluid flows.
Frequently Asked Questions
How often should brake hardware be replaced?
Replace hardware every 30,000 miles or when shim thickness drops below 0.040 in. SAE J442 recommends new shims with each pad service to keep braking consistent and quiet. If you notice any noise or uneven wear, inspect the hardware immediately and replace as needed.
What torque values should I use for caliper bolts?
Caliper bolts should be torqued to the value listed in your vehicle’s service manual. Many Honda models specify 85 ft‑lb. Apply the torque in a criss‑cross pattern and verify with a calibrated wrench.
Using the correct torque prevents bolt loosening and caliper misalignment.
Can I reuse old brake fluid after hardware replacement?
Re‑using old brake fluid after hardware work is not recommended because moisture and air can accumulate, reducing pedal firmness. A full fluid flush with fresh DOT 3/4/5.1 fluid restores performance and protects internal components. Perform the flush before re‑installing the caliper to ensure no contaminants enter the system.
Do I need to replace the rotor when swapping hardware?
You only need to replace the rotor if it is warped, scored, or below minimum thickness. A smooth, true rotor can be reused after cleaning and a light cut if within spec. Check rotor runout with a dial indicator; any reading over 0.002 in. warrants replacement.
What are the signs of failed brake hardware?
Failed brake hardware shows up as persistent squeal, vibration through the steering wheel, or a soft pedal feel. Uneven pad wear, especially one side wearing faster, also points to shim or clip issues. Addressing these signs promptly prevents more costly rotor or caliper damage.
Is it safe to do this repair on a driveway?
A driveway repair is safe if you use a sturdy jack, proper jack stands, and wheel chocks. Ensure the vehicle is on level ground and the parking brake is set. Avoid working under the car if you lack a second set of stands.

