How to Replace a Coil Spring: Quick and Easy Guide

Replacing a coil spring is a common DIY task that can make your car ride smoother and safer. If your vehicle is sagging or making noise, this is likely the culprit. You don't need special equipment for every step, but knowing what to look for prevents mistakes.

Manufacturer specifications indicate a typical coil spring has a free length of 12 to 14 inches before compression. Always check the installed height against your vehicle manual to avoid issues. We'll cover the visual cues that make this job successful.

How to Replace a Coil Spring

Replacing a coil spring restores proper ride height. Use a rated spring compressor. Inspect the perch pocket.

Torque the top nut to spec. Align the vehicle after.

A Seated Coil Spring Is a Visual Check, Not a Guess

You can tell a lot by looking at the spring while it's compressed. The coils should be evenly spaced without any bows or twists. If the spring is not level, it will cause the car to lean to one side.

Many DIYers skip this step and just push the spring into the seats. But a quick visual check shows if everything is aligned. Per the spring manufacturer instructions, the end coils must sit fully in the perch pockets.

Use a ruler or tape to measure the coil spacing at several points. This ensures the spring is not damaged during compression. Aggregate user reviews report fewer issues when this visual step is followed.

We recommend taking photos during compression to compare later. This visual confirmation prevents common installation errors. Features like progressive rate appear in the coil shape.

The pigtail end must be oriented correctly. Always confirm the color code or paint mark matches the original.

Replacing the Spring: What to Watch From the Wheel Off to the Last Bolt

You must confirm the axle, corner, and side before starting. Chock the wheels and place jack stands at the right lift points. Remove the wheel and inspect the broken coil visually.

Disconnect the sway bar end link, brake line bracket, and ABS wire.

Support the knuckle or control arm before removing the strut bolts. Index marks on the spring-to-perch and mount-to-tower help with alignment. Place the compressor claws opposite each other on the coils.

Take up the tension evenly until the spring loosens in both seats. Remove the top nut while holding the damper rod.

Transfer the old mount, bearing, isolator, boot, and bump stop to the new spring. Seat the new spring so the end coil drops fully into the pocket. Check that the spring sits level with no coil crossed on the perch lip.

Decompress slowly and watch for any shift. Tighten suspension bolts at ride height per the service procedure. Measure ride height at the specified body points.

Get a four-wheel alignment afterward to keep camber and toe on spec.

Strut-Captured Front Springs

Front springs sit in the MacPherson strut assembly. You need an external claw compressor for most passenger cars. The strut shaft thread must stay clean to avoid cross-threading the top nut.

Watch for the bearing plate arrow pointing the correct way. If the mount is worn, replace it at the same time. Check the upper strut mount for play before the wheel comes off.

The knuckle bolts require specific torque values from the vehicle manual. Support the control arm to prevent the strut from dropping too far. This setup often requires more visual checks than rear coils because of the tight strut tower space.

Pair the springs on both sides so ride height stays even.

Free-Standing Rear Coils

Rear coils often sit in multilink or solid-axle setups. You can use a bench-mounted screw compressor for these. The pigtail spring end usually needs the correct clock position.

Lower control arms may need support to keep the axle level. Inspect for rust in the spring seat pocket. The lower perch may have a different shape than the front.

Measure the free length against OEM specs before buying. This type of spring is easier to handle but still needs even compression. Watch for the rubber isolator to crush evenly.

Replace bump stops at the same time to restore suspension travel.

spring perch

Image source: Wikimedia Commons / Kieren (CC BY-SA)

Perch Pockets, Pigtails, and Mount Marks That Tell You It's Right

The perch pocket should be clean and free of rust. The pigtail must match the original clock position exactly. Upper mount marks or arrows show the correct orientation.

Look for the spring seat pocket to match the end coil shape. When you look at the image of a spring perch, you see the ideal seating position with the end coil fully dropped in. This visual tells you the spring is ready for installation.

The mount bearing index mark must align with the tower. Avoid reusing a twisted rubber isolator. The color code or paint mark on the new spring should match the old one.

After seating, the spring should sit level with even coil spacing.

building car ramps from wood helps create a stable work area. When you need to tighten the bolts, use an using an impact wrench on lug nuts for the right technique. Make sure to replace the strut mount if it's worn.

are more expensive tie rod ends worth it shows when to upgrade suspension parts. are acdelco tie rod ends good works well for most cars. Pricing for a quality coil can vary.

See how much do lug nuts cost for similar part pricing insights.

Frequently Asked Questions

How long does the job take?

Expect two to four hours for an experienced DIYer. Front struts usually take longer than rear coils. Plan extra time for photos and measurements.

What tools do I need?

You need a spring compressor rated for the coil diameter. A torque wrench and the vehicle manual are essential. Basic hand tools and safety glasses complete the list.

Can I do this without a lift?

Yes for many cars. Use jack stands and chock the wheels first. Support the knuckle before the strut bolts come out.

How do I know if the spring is installed right?

The end coil must sit fully in the perch pocket. The spring should sit level with no bows. Check the mount arrow and torque the top nut to spec.

Scroll to Top