A cam-timing code is why you're looking this up. You need to know how to replace a vvt solenoid before you pay for a phaser. The oil control valve is a small electric spool that meters oil into the camshaft phaser.
On many engines it sits on the valve cover with one bolt.
Manufacturer specs show the engine control module drives that coil with a duty cycle. It is not a simple on or off switch. As of 2026, aftermarket units often run $30 to $80, and many OEM pieces run $80 to $200.
Match the bank before the wrench work below.
How to Replace a Vvt Solenoid
Learning how to replace a vvt solenoid starts with the right bank. Unplug the connector and remove one bolt. Pull the valve straight out of the bore.
Fit a new O-ring and seat it fully. Torque the bolt to the engine spec, then clear codes.
VVT Solenoid Failure Symptoms
The light is the first clue. A scan tool will usually show a circuit code or a cam-angle code. Rough idle, a flat spot on tip-in, and worse fuel use often ride along with it.
Cold-start rattle is trickier. A short knock that fades can be a tired phaser or chain, not the solenoid. If the oil is low or black and thick, fix that before you condemn the valve.
In our research, these codes come up most often:
| Code | Meaning |
|---|---|
| P0010 | Bank 1 intake solenoid circuit |
| P0011 | Bank 1 intake cam over-advanced |
| P0012 | Bank 1 intake cam over-retarded |
| P0013 | Bank 1 exhaust solenoid circuit |
Bank 2 uses the same pattern from P0020 through P0024. A photo of the cover, with the plug marked intake or exhaust, stops a wrong-bank swap. Pull the code with a decent scan tool before you buy anything.
How the VVT Solenoid Works
Variable valve timing (VVT) moves the camshaft a few degrees while the engine runs. The solenoid, also called an oil control valve, is the gate for that oil.
Inside the body is a 12-volt coil and a spool. When the module pulses the coil, the spool sends oil to one side of the phaser or the other. Advance on one path.
Retard on the other.
A mesh screen sits in the oil inlet. An O-ring seals the bore. A diagram of the oil feed would show a small gallery passage.
It runs through that screen and into the phaser. Sludge packs the screen. Then the cam can't follow the command, even with a live coil.
After a code clear, the cam-timing monitor must run again before many inspections will pass. That monitor sits inside the OBD system the EPA requires on gasoline cars. More detail on these valves shows up in SAE papers on cam phasing.
Step-by-Step Visual Guide to Replacing a VVT Solenoid
What should you see before you start?
You should see one connector, one bolt, and the solenoid body on the cover or timing housing. Let the engine cool first so hot oil can't burn you. Disconnect the negative battery cable.
Record the code before you unplug anything.
If brackets hide the bolt, follow the layout for your engine code. Don't guess the bank from a generic picture. If the bolt is only reachable from below, use sturdy wooden ramps.
Don't crawl under a jack alone.
| Item | Job |
|---|---|
| Scan tool | Read the code and cam angle |
| Socket | Remove the one hold-down bolt |
| New O-ring | Seal the bore |
| Engine oil | Wet the seal before install |
Pull the old valve and seat the new one
- Release the lock tab and unplug the connector.
- Remove the hold-down bolt and pocket it.
- Pull the solenoid straight out. Do not pry sideways.
- Match length, screen, connector, and O-ring groove to the new part.
- Fish out any old O-ring left in the bore.
- Oil the new O-ring and push the valve in until the flange sits flush.
- Start the bolt by hand and tighten it to the OEM spec for that engine.
- Click the connector home and reconnect the battery.
What do you check once the bolt is tight?
You check cam angle on a road test, then look for oil at the bore. Clear the codes first. Desired angle and actual angle should track once the engine is warm.
Wetness after a heat cycle means the seal didn't seat.
Glance at oily plug tips while the area is open. Oil there means the solenoid was never the whole story. Don't hide a hard start by spraying starting fluid.
Common Mistakes to Avoid When Replacing a VVT Solenoid
The usual miss is a new valve on a bad phaser or low oil pressure. A solenoid will not quiet a stretched chain.
Next is the wrong bank. Intake and exhaust units can look identical and still be different parts. Match the part number to the VIN.
A photo can lie. The body looks seated, but a gap at the flange means the O-ring rolled. A ring left in the bore leaks the same way.
There is no universal torque. Use the spec for your engine. Guessing strips the aluminum hole.
Treat it like pricier chassis parts. Pay extra only when the O-ring, screen, and plug match the original.
Frequently Asked Questions
What tools do you need to replace a VVT solenoid?
You need a scan tool, a socket, a matched solenoid with a new O-ring, and towels. Most hold-down bolts are 8 mm or 10 mm. Add a torque wrench because the hole is aluminum.
A photo of the connector stops a reversed plug.
Can you drive with a bad VVT solenoid?
You can usually drive home, but don't leave it for weeks. The cam can stay advanced or retarded, so idle and power fall off. Fuel use climbs.
A steady light can fail an emissions inspection. Check the oil level before you go farther.
How long does a VVT solenoid replacement take?
Plan 30 to 60 minutes when the solenoid is on the valve cover. Intake or cowl access can push it past two hours. Unplugging and unbolting is the fast part.
The road test and a heat-cycle leak check take the rest.
Will a new VVT solenoid fix code P0011?
It will only if the solenoid or its screen has failed. P0011 means the bank 1 intake cam is over-advanced. Low oil, the wrong viscosity, or a worn phaser set the same code.
If the oil is sludge, change it before you buy the part.

