Replacing a sway bar bushing is a common DIY task that restores your vehicle's handling. If the car is bouncy or making clunking noises, the bushings may be worn. You can spot this problem by inspecting from underneath.
Aggregate reviews report that these bushings typically last 50,000 to 80,000 miles. Manufacturer specifications indicate the inner diameter is usually 22mm for most vehicles. As of 2026, many mechanics recommend replacing them proactively to avoid handling issues.
This guide shows you exactly how to replace a sway bar bushing safely and correctly.
How to Replace a Sway Bar Bushing
Support the sway bar with blocks. Remove the bracket bolts. Pry out the old bushing.
Install the new split bushing. Torque the brackets at ride height. Check for noise after driving.
Always use a torque wrench for accuracy. Verify the bushing is fully seated. Test drive to confirm handling improvements.
How to Spot a Worn Sway Bar Bushing From Under the Car
To spot a worn sway bar bushing, start by safely lifting your vehicle using how to build car ramps from wood. Crawl underneath and look for tears, cracks, or missing rubber. The bushing should be snug without excessive play.
Listen for clunks when turning or hitting bumps. If the bushing is damaged, it can cause uneven tire wear and poor handling. Check the split design for signs of separation.
Use a pry bar to test for movement. Replace it before it fails completely. This inspection takes about 15 minutes but prevents bigger problems later.
Manufacturer specs confirm the rubber should remain flexible. If it's hard or brittle, it's time for replacement. Use what is a car recovery point when lifting to stay safe.
Aggregate reviews report that many owners miss these signs until the clunking starts.
Rubber, Poly, and the Tools That Actually Fit the Job
Rubber bushings offer better ride comfort and isolation from road noise. Polyurethane versions provide better performance and durability for spirited driving. Choose rubber for daily drivers and poly for performance cars.
The materials differ in hardness and flexibility. Rubber is easier to install but wears faster in hot climates. Poly lasts longer but can be stiffer.
For tools, you need a socket set, torque wrench, pry bar, bushing press or arbor press, and replacement kit. Refer to how to use an impact wrench on lug nuts for similar torque work. Also, are more expensive tie rod ends worth it if considering upgraded components.
The split bushing design makes installation easier than pressed ones. Get the right size for your vehicle model. Measure the old bushing before buying.
This section helps you decide which type fits your needs and what tools you'll need for success. Watch for signs of degradation in the rubber and plan for the job accordingly.
Replacing the Bushing: Bracket, Split, and Ride Height
The sway bar has brackets that mount to the subframe. The split bushing sits inside the bracket. Ride height affects the preload on the bushing.
Too much torque can crush the bushing. Too little can cause it to move. Follow the vehicle manual for exact specs.
The split design allows easy installation without removing the bar. Look at the photo for the split bushing.

Notice how the cut runs lengthwise for easy prying. This method saves time compared to full bar removal. Use Loctite on the bolts to prevent loosening.
Torque in a crisscross pattern. This section covers the key components and why ride height matters. Per SAE standards for torque application (see SAE standards), proper preload keeps everything secure during driving.
Check your local availability of bushing kits before starting.
Support the Bar Before the Brackets Come Off
Before removing the brackets, support the sway bar with wood blocks or jack stands. This prevents it from dropping and damaging other parts. Place the supports at the ends of the bar.
Loosen the bracket bolts but don't remove them yet. This allows the bar to sit in place. Once supported, you can remove the bolts completely.
The bar should stay level. If it sags, add more support. This step is critical to avoid injury or damage.
Use how to remove step pads from running boards to access the area if needed. Always double check the supports are stable. This preparation makes the rest of the job much easier.
Monitor the bar closely while working underneath. Re tight all connections only after the new bushing is seated. This approach reduces risk and ensures a smooth install overall.

